Dealing with a Sudden Water Heater Shutdown: Key Steps
Dealing with a Sudden Water Heater Shutdown: Key Steps
Blog Article
We have unearthed this great article about Hot Water Heater Repair down the page on the internet and reckoned it made sense to share it with you over here.
Several modern-day homes take advantage of an electric water heater for their heater, as a result of its ease and also convenience of use. Nonetheless, similar to any other electric devices, troubles might develop with its usage, unexpectedly. It can be truly frustrating to awaken to a cold shower as opposed to a hot one or having your bathroom with water that isn't warm sufficient and even also warm. Whatever the case may be, hot water heater troubles can be quite nerve-racking. Luckily, we have actually made a listing of possible solutions to your water heater issues. There are a variety of variables that could trigger a lot of these issues, it could be an issue with the power supply, the electric burner, or the thermostat. Prior to doing anything, ensure you shut off the major power supply for safety and security. Whatever the problem is, getting it taken care of should not position way too much of an issue if you follow these steps:
Inspect Your Power Supply:
As fundamental as this may seem, it is extremely essential. Without ample power, your water heater will not function. So the first thing to do when your water suddenly stops working is to confirm that it isn't a power problem. Examine if the fuse is burnt out or the circuit breaker tripped. If the breaker is the concern, simply transform it off and on once again. Replace any kind of busted or worn-out fuse. Test the home appliance with power after these changes to see if it's now functioning.
Examine the Burner in the Hot Water Heater:
If it's not a power issue, then try taking a look at your heating element if it is still working. Evaluate each of your burner to be sure the issue isn't with any of them. If any of them is damaged, change that component and then check whether the hot water is back on.
Inspect Your Thermostat:
If your hot water heater still isn't working or the water coming out isn't hot sufficient, you may need to examine the temperature level settings on your upper thermostat. Guarantee the breaker is switched off prior to doing anything. Open the accessibility panel and press the red button for temperature level reset over the thermostat. This must help warm the water. Transform the circuit breaker back on and examine if the issue has been fixed.
Call A Specialist:
If after changing all defective components and resetting your temperature, the hot water heater still isn't working, you may require to get in touch with a professional plumber for a professional point of view. The problem with your heating unit could be that the cold and hot faucets have been changed or it might be undersized for the amount of hot water needed in your home. Whatever the situation may be, an expert plumber would certainly assist address the trouble.
Conclusion
Water heater problems are not constantly major. Most of them are due to minor issues like a blown fuse or worn-out heating element. Replacing the defective parts must do the trick. Nonetheless, if you are still unable to fix the problem, give a call to your nearby plumber to come to get it repaired.
What Would Cause My Electric Water Heater to Stop Working?
Your water heater is one of the most forgotten-about appliances in your home—until it quits working. Once you realize that there’s no hot water, the water heater jumps up to become the most noticeable appliance you have. No one in your family will be happy until you get the water heater fixed.
To fix an electric water heater as soon as possible, follow the troubleshooting advice discussed below.
Basic Water Heater Troubleshooting
Fortunately, you may be restore the hot water supply simply by resetting the house circuit breaker for the water heater. A tripped circuit breaker is one of the top causes of water heater failures. Shut the hot water heater breaker off then turn it back on. Give the water heater a half hour to heat up (if it’s working) and then check for hot water through one of your faucets.
If you get hot water after resetting the breaker, then the problem may be fixed if the breaker inadvertently tripped and it doesn’t continue tripping.
If the water heater breaker trips again, then you’ll likely need to have a service technician examine and repair the water heater. The service technician will check the circuit breaker and electrical supply wiring for the water heater. A short in the supply wiring or a bad circuit breaker could be causing the breaker to trip. An internal failure such as a broken heating element can also cause the breaker to continue tripping.
When resetting the water heater circuit breaker doesn’t work at all, then the water heater may be getting power while an internal water heater failure is causing the problem.
Conduct Advanced DIY Water Heater Troubleshooting
If the water heater doesn’t work after resetting the high-temperature limit switch, then you’ll need to either conduct some advanced water heater troubleshooting or have a service technician diagnose and repair the water heater failure.
Sears Technicians created a safe and highly-successful DIY advanced troubleshooting video to help you determine the cause of a water heating failure if you want to try to fix the problem yourself. Follow the advice in this video to find and fix the cause of the heating failure on your own:
The video begins with the basic troubleshooting described in the first 2 sections described above. It then goes on to guide you through checking water heater components to safely find the cause of the water heating failure.
If you get to a point in the troubleshooting where you’re not completely confident that you can safely continue, schedule a service technician to diagnose and repair the water heater.
The DIY water heater troubleshooting shown in the above video differs from the diagnosis techniques that service technicians typically use when examining a water heater to find the cause of a heating failure. Safe DIY troubleshooting doesn’t rely on live voltage checks while service technicians often use live voltage checks to quickly find the cause of water heater failures.
While many DIY’ers have been able to find the cause of water heater failures using troubleshooting advice shown in the video, some failures such as a bad circuit breaker can only be found using live voltage checks which should only be conducted by a trained service technician.
Sears Technicians have the training, tools and expertise to quickly find the cause of a water heater failure. Rely on our technicians to diagnose and repair your water heater or any other appliance in your home that quits working.
While the technician is in your home, take advantage of appliance Cleaning & Maintenance offers that the tech discusses with you. Keeping your appliances well-maintained will help them work more efficiently and last longer. Regular professional maintenance will also help prevent costly breakdowns of the appliances you depend on every day.
https://www.searshomeservices.com/blog/what-would-cause-my-electric-water-heater-to-stop-working
We hope you liked our section on Hot Water Heater Repair. Thanks for finding the time to browse our article post. Sharing is nice. Helping others is fun. I am grateful for your time. Kindly come visit our site back soon.
Schedule A Free Estimate Report this page